• Recente
Tekko32 f4 metal 65a 4in1 esc Blheli32 4-6s 128k Sensor de corrente analógica a bordo F4 MCU para RC Drone FPV Racing Diy Toy
zoom_in

Tekko32 f4 metal 65a 4in1 esc Blheli32 4-6s 128k Sensor de corrente analógica a bordo F4 MCU para RC Drone FPV Racing Diy Toy

€ 0.67

Quantidade do produto
check Existente

Tekko32 F4 Metal 65a 4in1 ESC BLHELI32 4-6 S 128 K Sensor de corrente analógica a bordo F4 MCU para RC Drone FPV Racing DIY Toy Tekko32 F4 Metal 65a 4in1 ESC BLHELI32 4-6 S 128 K Sensor de corrente analógica a bordo F4 MCU para RC Drone FPV Racing DIY Toy. Recursos : F4 MCU / BLHELI32 / METAL CASE MOSFET / PWM Saída 96k / 4 ~ 6s O novo BLHELI32 ESC adaptou o MCU F4, que fornecerá um controle mais suave e uma velocidade de resposta mais rápida. Especificação : F4 MCU com o firmware BLHELI32 Saída máxima de PWM até 96k (padrão 48 K) A taxa de escala de amperagem foi ajustada para 168. O 4in1 possui sensor de corrente analógica a bordo e a função TLM (então nenhuma leitura atual sobre TLM) usa moseado de metal para Mosfet para Melhor dissipação de calor sem saída BEC suporta LIPO 4-6 S Capacitor extra necessário para 6s (1000 UF 35 V para uso 6 S.) Importante se você deseja executar este 4in1 em alta corrente. O cabo de entrada (de Lipo a 4in1) deve ser de pelo menos 12awg e bem soldado. Pacote incluído : 1x Tekko32 F4 Metal 4in1 65a ESC 4 X M3 Anti-vibração Silicone Grommet Inserção 1x Capacitor eletrolítico : 1000 UF 35 V 1x 8pin a 8pin 1 mm de cabo 65mm 1x 8pin a 8pin 1 mm 25 mm 25 mm.

F4 MCU with BLHELI32 firmware :
Maximum PWM output upto 96K (default 48K) :
Amperage meter scale ratio has been adjusted to 168. :
The 4in1 has onboard analog current sensor, and TLM function (then no current reading over TLM) :
Uses metal case mosfet for better heat dissipation :
No output BEC :
Supports Lipo 4-6S :
Extra capacitor needed for 6s (1000uf 35v for 6s usage.) :
Dimensions:
43 x 44mm
Mounting holes:
30.5×30.5mm(M4)
Weight:
15.8g
Notice:
The air flow is very important if you want to run this 4in1 in high current. :
The input cable (from Lipo to 4in1) should be at least 12AWG and well soldered. :
Package Included:
1x Tekko32 F4 Metal 4in1 65A ESC :
4x M3 Anti-Vibration Silicone Grommet Insert :
1x Electrolytic capacitor:
1000uF 35v
1x 8pin to 8pin 1mm pitch 65mm cable :
1x 8pin to 8pin 1mm pitch 25mm cable :

Best Sellers..